aFe – MACH Force-XP 2.5in 409 SS Cat-Back Hi-Tuck Exhaust – 10-19 Toyota 4Runner V6-4.0L

aFe – MACH Force-XP 2.5in 409 SS Cat-Back Hi-Tuck Exhaust – 10-19 Toyota 4Runner V6-4.0L Performance Gains: In testing, the cat-back exhaust system resulted in gains up to 11 horsepower and 19 lbs. x ft. of torque, as measured on our in-house dyno. Flow and Performance: This Mach Force-XP Series exhaust system is constructed of 2-1/2″ mandrel bent 409 stainless steel for maximum flow and low turbulence increasing torque, horsepower and improved throttle response. Aggressive Sound: A 22″ less restrictive, muffler absorbs high pitch tones producing a powerful, aggressive, smooth tone under load. Hi-Tuck Design: Provides maximum clearance when off-roading to give your 4Runner extra clearance during extreme angle climbs or descents. Perfect Fit: OE style bayonet hangers are used to maintain a stable pipe location during high vibration and high heat conditions. The bayonet tip holds the hanger bushing in place for an OE style fit that does not change with time. Note: Fits all 4Runner models including 4Runners equipped with Kinetic Dynamic Suspension System (KDSS). Emissions Disclaimer: This product does not require a CARB EO#. aFe – POWER exhaust systems are engineered and manufactured in our Corona, California facility. Whether you are bounding off-road or racing to soccer practice, aFe – POWER’s MACH Force-Xp cat-back exhaust system for your Toyota 4Runner with the V6-4.0L engine will get you there with speed and style. Designed from 2-1/2″ mandrel bent, 409 stainless steel, this exhaust system offers greater flow to deliver more torque and horsepower than the factory exhaust. This four piece designed cat-back system utilizes a less-restricting muffler to improve your 4Runner’s performance while maintaining a deep, smooth tone. 100% hand MIG-welded by certified craftsmen for proven quality and durability, the MACH Force-Xp exhaust system is designed with a Hi-Tuck style tip to give your 4Runner extra clearance during extreme angle climbs and descents on or off-road. Product Details Up to 11 HP & 19 Lbs. x Ft. TQ 2-1/2″ Mandrel-Bent 409 Stainless Steel Hi-Tuck Design for Clearance and Greater Approach Angles Includes High-Flow 22″ Long High-Flow Muffler High Quality Hardware and Clamps for Durability and Easy Installation 100% Hand MIG Welded for Proven Quality and Durability Fits with Kinetic Dynamic Suspension System (KDSS) Installation instructions Dyno chart Fitment Year Make Model Sub-Model 2010-2023 Toyota 4Runner V6-4.0L aFe’s Warranty For information on aFe’s warranty terms and conditions, please click here. Purchase Disclaimer: You are hereby informed and warned to check your local, state, and federal laws before buying and installing these or any aftermarket parts to be sure whether usage is in violation. All installation-risk and use-risk is borne by the end-user and installer of these parts. Bolt Motorsports does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Bolt Motorsports will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 CFR Section 86.1854.12(a)(3), Clean Air Act 40 CFR 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls. In accordance with local laws and regulations, Bolt Motorsports will not ship parts to locations where usage or installation of said part would be in violation of the aforementioned acts. Reviews There are no reviews yet. Be the first to review “aFe – MACH Force-XP 2.5in 409 SS Cat-Back Hi-Tuck Exhaust – 10-19 Toyota 4Runner V6-4.0L” Cancel replyYour email address will not be published. Required fields are marked *Your rating * Rate… Perfect Good Average Not that bad Very poor Your review *Name * Email * Save my name, email, and website in this browser for the next time I comment.